11-06-2012, 09:55 AM
Jeffrey
I sensed that this site was going to be an excellent resource for a clear look at the collapse sequence.
In the section on bolted splices:
http://www.sharpprintinginc.com/911/inde...on=539:539
I find reference to what had seemed the most likely method of facilitating total collapse with the plausible antecedent of the plane penetration and fire:
BEGIN EXCERPT
From the available literature we discovered that there is a horizontal plane on the 98th floor right through the core where all core columns naturally break in two if the connecting bolts are removed. Every 114+ story core column is already "cut" at the 98th floor. All one need do is remove the top bolt connectors and push the top part over a little, taking advantage of existing "cuts" by manipulating (removable) bolt connections.
Here is a picture of a typical bolted splice connection along a typical H beam.
[ATTACH=CONFIG]3835[/ATTACH]
In this case the plates are welded to the lower column section, For WTC1 they were bolted.
If a demo team had access to such connections it would be rather dumb of them not to exploit them.
Why nuke the building or attack it with space beams if you can just knock the top H beam sections off the bottom ones in the collapse initiation region?
Why cut steel when you don't have to?
How many simple ways can you think of to knock the top column section off the bottom one with minimal force? Why not just remove a few bolts with a wrench? Why not all of them?
>>>>>>>>>>>>>>>>>>>>
My point is that it doesn't require a genius to figure out how to initiate the WTC1 collapse. No nukes or space beams required.
All core column bolted connections in the collapse initiation zone are on floors 89, 92, 95, 98, 101, 104 about 3 feet above the flooring. These are the natural targets so it is important to carefully look for unusual activity on these floors during the 30 minutes leading up to collapse.
END EXCERPT
Heretofore there seemed to be a false choice between an official explanation which explained nothing, and a speculative causality which relied on science fiction.
I hold fast to the imperative of the total collapse attributable to evildoers overseas as a Hearstian casus belli.
The site-as-book you recommend counsels careful observation and measurement (lacking in official and contrarian models) and suggestsas I'd sensed as tactically appropriatethe simple sabotage insuring catastrophic failure.
As noted, given the "caged" condition, the elements were confined in movement, that is, directed downward as a controlled demolition sitting on go.
As with Thy Will Be Done: The Conquest of the Amazon: Nelson Rockefeller and Evangelism in the Age of Oil by Gerard Colby and Charlotte Dennett, the book on the towers has many moving parts, the interplay of which is a fascinating study of materials pushed to the point of failure by relentless forces.
We continue.
I sensed that this site was going to be an excellent resource for a clear look at the collapse sequence.
In the section on bolted splices:
http://www.sharpprintinginc.com/911/inde...on=539:539
I find reference to what had seemed the most likely method of facilitating total collapse with the plausible antecedent of the plane penetration and fire:
BEGIN EXCERPT
From the available literature we discovered that there is a horizontal plane on the 98th floor right through the core where all core columns naturally break in two if the connecting bolts are removed. Every 114+ story core column is already "cut" at the 98th floor. All one need do is remove the top bolt connectors and push the top part over a little, taking advantage of existing "cuts" by manipulating (removable) bolt connections.
Here is a picture of a typical bolted splice connection along a typical H beam.
[ATTACH=CONFIG]3835[/ATTACH]
In this case the plates are welded to the lower column section, For WTC1 they were bolted.
If a demo team had access to such connections it would be rather dumb of them not to exploit them.
Why nuke the building or attack it with space beams if you can just knock the top H beam sections off the bottom ones in the collapse initiation region?
Why cut steel when you don't have to?
How many simple ways can you think of to knock the top column section off the bottom one with minimal force? Why not just remove a few bolts with a wrench? Why not all of them?
>>>>>>>>>>>>>>>>>>>>
My point is that it doesn't require a genius to figure out how to initiate the WTC1 collapse. No nukes or space beams required.
All core column bolted connections in the collapse initiation zone are on floors 89, 92, 95, 98, 101, 104 about 3 feet above the flooring. These are the natural targets so it is important to carefully look for unusual activity on these floors during the 30 minutes leading up to collapse.
END EXCERPT
Heretofore there seemed to be a false choice between an official explanation which explained nothing, and a speculative causality which relied on science fiction.
I hold fast to the imperative of the total collapse attributable to evildoers overseas as a Hearstian casus belli.
The site-as-book you recommend counsels careful observation and measurement (lacking in official and contrarian models) and suggestsas I'd sensed as tactically appropriatethe simple sabotage insuring catastrophic failure.
As noted, given the "caged" condition, the elements were confined in movement, that is, directed downward as a controlled demolition sitting on go.
As with Thy Will Be Done: The Conquest of the Amazon: Nelson Rockefeller and Evangelism in the Age of Oil by Gerard Colby and Charlotte Dennett, the book on the towers has many moving parts, the interplay of which is a fascinating study of materials pushed to the point of failure by relentless forces.
We continue.